GONOTEC OSMOMAT 030 PDF

Moogujar The resulting ice formation causes the temperature to rise to the freezing point of the solution. Thermistor probe adjustment along Y-axis. Restriction of the possibilities for manufacturers to enforce such warranty exclusions and restrictions c. Analog port for continuous recording of the temperature development with a compensating recorder.

Author:Doukree Arakus
Country:Costa Rica
Language:English (Spanish)
Genre:Video
Published (Last):9 November 2019
Pages:111
PDF File Size:5.24 Mb
ePub File Size:6.76 Mb
ISBN:182-6-23842-968-5
Downloads:34393
Price:Free* [*Free Regsitration Required]
Uploader:Vudor



Moogujar The resulting ice formation causes the temperature to rise to the freezing point of the solution. Thermistor probe adjustment along Y-axis. Restriction of the possibilities for manufacturers to enforce such warranty exclusions and restrictions c.

Analog port for continuous recording of the temperature development with a compensating recorder. This will osmimat the measurement system. Gonotec Osmomat Forums Questions Discussions Help LabWrench These operating instructions help you gain a osjomat understanding of the design, the measurement principle, maintenance and servicing of the unit.

The temperature remains constant because further heat removal does not result in a lowering of the temperature but the formation of ice. The end of the paper must be between the ribbon and the cartridge.

Such actions invalidate the compliance statement and transfer responsibility to the originator of said actions. This means that at the time the point temperature is measured, the concentration is higher than in the original solution. The thermistor probe is now immersed in the water. A mechanical problem is preventing the movement of the needle. For questions about using the LabWrench web site please call us. Gonotec Osmomat Always use a new measuring vessel with fresh calibration solution for each new measurement.

All countries outside the EU. The crystallization enthalpy causes an immediate rise in temperature up to the freezing point of the remaining, somewhat more highly concentrated osmomah. Thermistor with mounting plate Next, insert the plug of the connector cable into the connector and guide the thermistor cable into the groove along the side. Re-attach the Plexiglas shield. Analog interface with pin assignment 8. NaCl solutions for osmometry based on Geigy scientific tables, 8th edition Remove Connector these also Figure 5: The Welch CRVpro vacuum pumps are suitable for use in life sciences and biotechnology research Any departure from the specifications or independent modifications of the unit without the express odmomat of Gonotec GmbH may result in a violation of CE requirements.

The OSMOMAT initiates crystallization by injecting the sample with a gonotwc steel needle that is cooled by a secondary upper cooling system and at the tip of which small ice crystals have formed through moisture in the air. When calibrating, be aware that the thermistor probe may still be contaminated with sample residues gonoec previous measurements. The calculated freezing point temperature is recorded by the unit and, using the calibration value, converted into an osmolality value and output to the digital display.

During the time in which both ice and solution are present, a freezing plateau then forms. Calibration cannot help minimize damage in the case of malfunction. The output voltage of the analog output can be aligned with the alignment potentiometer for older flatbed recorders. The design of the Osmomat auto is based on ten years of experience with the measuring principle of the Osmomat After undercooling has occurred, the needle will automatically be submerged, initiating crystallization.

The moment the undercooling temperature is reached, crystallization is initiated automatically by the injection of ice crystals, and an acoustic signal sounds. Opening the printer C. REF Article number or order number The following pages provide you with a step-by-step introduction to using, maintaining and servicing the measurement equipment. Replacing the ribbon D. Besides water, two other calibration points are possible. A plateau occurs here as well, but it is inclined. Osmomat The gonoted number helps our service technicians to more quickly record the unit and determine a procedure.

Use a soft paper towel to thoroughly clean the thermistor probe after each measurement. In the pharmaceutical industry and research, the Osmomat is used to test various aqueous solutions saline drips, etc. The drop of water may be the result of ice crystals falling from the upper cooling system.

There must be no visible air bubbles in the liquid! Gonotec Osmomat Cryoscopic Osmometer. The following countries and regions are excepted: Special models using V or V are also available. If the sample consists of water solventequilibrium is achieved as long as the sample contains water and ice. The purpose of the adjustment is align the center axis of the cooling clamp with the thermistor axis see Figure 7: Monday, 20 September, Supplied by: Standardized calibration and reference solutions and an adjustment tool are used to check the internal quality control mechanism.

The corresponding NaCl concentrations can be found in the appendix to these operating instructions. The unit emits no harmful substances either in operation or while switched off. The bore can first be rinsed using a spray bottle of water to clean out sample residues, which can rub off and accumulate on the interior surface over time. It must be taken into consideration, however, that the osmolality does not change in proportion to the dilution ratio, since the degree of electrolyte dissociation during dilution is different for each substance.

TOP 10 Related.

LAS SOLDADERAS ELENA PONIATOWSKA PDF

Osmometers

Grozshura A reading is obtained that is automatically adopted as the calibration value according to the prior setting and output to the digital display. A sequential number is printed out along with the measurement results. All countries outside the EU. Appendix 51 Appendix Returning Parts for Warranty Repair or Credit All products returned for repair or credit must be prepared as follows: Thermistor with mounting plate The serial number helps our service technicians to more quickly record the unit and determine a procedure.

ALTRONIX 6060 PDF

GONOTEC OSMOMAT 030 PDF

.

Related Articles